★ FREE SHIPPING ON ALL ACCESSORIES ★
with purchase of any Salt / Sand Spreader
FISHER SALT / SAND SPREADER ACCESSORIES
Truck Bed / Hopper Spreaders
return to Fisher Snow Plow Product
Extension Collars
An extension collar is available as an accessory to increase material capacity for vehicles that can handle the additional weight. 0.25 cu yd extension collars available for the 0.35 cu yd hoppers and 0.5 cu yd extension collars available for the 0.7 cu yd hoppers.
Part Number:
#85698 For 0.35 cu yd Models
#85699 For 0.7 cu yd Models
50-Gallon Pre-Wet & Direct Liquid Application Kit
With the addition of this accessory to the 0.7 cu yd model, operators will have the ability to pre-wet materials or spray brine directly onto the driving surface for anti-icing applications. The accessory kit includes two 25-gallon pre-wet tanks, a pump and a spray kit.
Part Number:
#85695 For 0.7 cu yd Models
Spill Guard Kit
A Spill Guard Kit provides the loader with an improved line of sight to the hopper edges, extending the edges of the hopper to 60" for the 0.35 cu yd model and 75.5" for the 0.7 cu yd model. This allows loading with a 5' loader bucket and prevents overflow and spill into the bed of the vehicle.
Part Number:
#85696 30" Kit for 0.35 cu yd Models
#85697 43" Kit for 0.7 cu yd Models
LED Work Light Kit
See more to do more with the Work Light Kit for better visibility at the rear of your spreader at night. Encased in anodized aluminum, and good to less than minus 20 degrees, this LED work light will put over 1000 lumens where you need them, when you need them. The LEDs mean low amp draw, so you can easily use more than one.
Part Number:
#99505-1 For All Models
LED Strobe Light Kit
See more to do more with the Work Light Kit for better visibility at the rear of your spreader at night. Encased in anodized aluminum, and good to less than minus 20 degrees, this LED work light will put over 1000 lumens where you need them, when you need them. The LEDs mean low amp draw, so you can easily use more than one.
Part Number:
#99494 For All Models
Central Point Grease Kit
The Central Point Grease Kit provides easy access to grease points, simplifying preventative maintenance greasing that is essential to maximize bearing life.
Part Number:
#11763 For 0.7 cu yd Models
Vibrator Kit
Loosen up stubborn materials and prevent bridging with this Vibrator Kit. Featuring a 200V DC vibrator motor in a metal housing, our vibrator will help prevent bridging and clogging, improving material flow so you can do your job faster and better.
Part Number:
#76668 For All Models
Inverted V Kit
Reduce heavy startup loads on the drivetrain and potential bridging during operations with the optional inverted V. Made of 12 gauge 201 stainless steel, the inverted V is strong and corrosion resistant, for use in highly demanding environments. The inverted V is easy to assemble and install and will provide years of trouble free use.
Part Number:
#85706 For 0.35 cu yd Models
#85707 For 0.7 cu yd Models
Ratchet Tie-Down Kit
This Tie-Down Kit provides additional in-bed stability and security. The 4,000 pound, high-strength shipping straps allow you to add an extra measure of safety as you move tons of salt down the road. Each kit includes four ratchet tie down assemblies. (Hoppers require bolting to the truck frame for proper operator safety.)
Part Number:
#68790 For All Models
Truck Up-Lift Kit
This kit contains a longer truck harness, license plate kit, CHMSL kit, and a ratchet tie down kit so the 0.35 cu yd hopper can be used in place of an auger tailgate spreader when using sand.
Part Number:
#85693 For 0.35 cu yd Models
Spreader Control Adapter Plate for Cup Holder Mount
Gain the flexibility and easy installation benefits of the cup holder control mount with every spreader installation using the new Spreader Control Adapter Plate Kit. Kit contains a durable metal mounting plate and hardware. Cup Holder Mount not included, order separately (#82006).
Part Number:
#82018 For All Models
Control Cup Holder Mount
The Control Cup Holder Mount is designed to fit firmly in most vehicle cup holders. It's a genuine, factory-tough accessory specifically engineered to securely hold FISHER hand-held or joystick controls and all types of smart phone devices (not included with mount). This flexible gooseneck mount has a 360-degree rotation and ensures optimal, customizable positioning.
Part Number:
#82006 For All Models
License Plate Kit
Stay street legal with this illuminated License Plate Kit for your alternate license plate location. Providing convenient mount methods and lighting in a high impact plastic casing, the license plate kit allows you to move your license to a spot that is visible and legally compliant. Don't leave without it. Required if using 0.35 cu yd hopper on a truck.
Part Number:
#85694 For 0.35 cu yd Models
Vehicle-Side Harness Kit
The Vehicle-Side Harness Kit contains components to replace harnessing on the truck or wire a second truck to operate the spreader.
Part Number:
#78402 For 0.7 cu yd Models
#85692 For 0.35 cu yd Models
Dielectric Grease
Keep your FISHER plow running strong. Apply our specially formulated dielectric grease after each use to prevent corrosion caused by electrolysis and highly corrosive de-icing agents.
Part Number:
#22400K 2 oz tube
Freeze Guard Grease
Specially formulated to protect moving components in arctic mining conditions, this grease is ideal for bearings, hinges and pivot bolts on snow and ice control equipment. The custom formula maintains viscosity from -40 up to 300 degrees, and military-grade, corrosion-prevention additives protect equipment from corrosion without harmful environmental impact. FREEZE GUARD Grease is available in cartridges, pails, totes and drums.
Part Number:
#72901 14oz. Cartridges
#72902 7 lb Pail
#72903 120 lb Tote
#72904 400 lb Drum
Pre-Wet System
The pre-wet system accessory allows the operator to activate deicing material by applying a liquid deicing agent directly on the material prior to leaving the hopper, providing you with increased material efficiency and superior ice control.
Part Number:
#76400 ON/OFF Pump Kit
#76420 Full Feature Pump Kit, FISHER
#76425 Pre-Wet 50 Gal Tank Kit* (Two 25 gal tanks)
#76450 Pre-Wet 100 Gal Tank Kit* (Two 50 gal tanks)
*Additional tank kits are not compatible with a vibrator
Poly Lid Kit
Shields de-icing material from the elements, locks out moisture to prevent material bridging and protects against material overflow while loading.
Part Number:
#72750 Regular Capacity
#72770 High Capacity
Spill Guard Kit
Available in 50" and 70" widths to cover the full range of STEEL-CASTER hopper spreaders, the Spill Guard Kit provides the loader with an improved line of sight to the hopper edges, while preventing material from overflowing into the bed of the truck from off-center loading.
Part Number:
#81119 70" Kit
#81120 50" Kit
License Plate Kit
Stay legal with our quality illuminated License Plate Kit. This genuine FISHER license plate kit has been specifically designed for your hopper and allows you to move your license plate to a spot that is visible and legally compliant.
Part Number:
#99686 For All Models
Strobe Light Kit
Make sure you're seen, day or night, with our complete hopper Strobe Light system. Constructed from high impact plastic, and rated beyond -20deg F, this yellow LED strobe system has been designed to last and will ensure that you're seen in even the worst of conditions.
Part Number:
#99494 For All Models
Vibrator Kit
Designed to help move stubborn material and prevent bridging, a genuine FISHER® Vibrator system will ensure that less-than-ideal material, which is prone to bridging and clogging, will not hold you up when you need to be on the move.
Part Number:
#76668 For All Models*
*Only compatible with one 50 gal pre-wet tank kit or one 100 gal pre-wet tank kit
Work Light Kit
A genuine FISHER Work Light system will grant you increased visibility at the rear of your spreader. Encased in anodized aluminum, and rated beyond -20º F, this LED Work Light system projects over 1000 lumens to help you monitor material distribution and illuminate potential hazards while backing up.
Part Number:
#99505-1 For All Models
Secondary Work Light Kit
Take it up a notch with a genuine FISHER secondary work light kit. Designed to integrate with our work light kit (99505-1), this accessory kit will provide an addition 1000 lumens of light on the opposite side of your FISHER spreader.
Part Number:
#99732-1 For All Models
6" Side Extensions
Increase the capacity of your STEEL-CASTER hopper spreader with this 6" Side Extensions Kit. The increase in capacity will vary depending on the size of your spreader; increased material capacity will vary from .5 to 1 yard. Each kit contains the corner brackets, hardware and installation instructions, but does not provide the side board material.
Part Number:
#99488 For All Models
Central Point Grease Kit
The Central Point Grease Kit provides easy access to grease points, simplifying preventative maintenance greasing that is essential to maximize bearing life.
Part Number:
#11763 For All Models
Tie-Down Chain Kit
A Tie-Down Chain Kit provides additional in-bed stability and security. 72 inches of high-strength steel chain and binder allow you to add an extra measure of safety as you move tons of material down the road. Each kit contains four chain binder assemblies. (Hoppers require bolting to the truck frame for proper operator safety.)
Part Number:
#99690 For All Models
Master Accessory Harness
Integrate all your accessories with this convenient kit. Includes all the wiring needed to go from cab to spreader, an in-cab control panel, and rear of hopper storage for accessory fuses and relays, allowing total integration of our plug and play accessories. Hydraulic model master accessory harness kit shown.
Part Number:
#99629 For All Gas Models
#99627 For All Hydraulic Models
Vehicle-Side Harness Kit
The Vehicle-Side Harness Kit contains components to replace harnessing on the truck or wire a second truck to operate the spreader.
Part Number:
#78402 For All Models
Spreader Control Adapter Plate for Cup Holder Mount
Gain the flexibility and easy installation benefits of the cup holder control mount with every spreader installation using the new Spreader Control Adapter Plate Kit. Kit contains a durable metal mounting plate and hardware. Cup Holder Mount not included, order separately (#82006).
Part Number:
#82018 For All Models
Control Cup Holder Mount
The Control Cup Holder Mount is designed to fit firmly in most vehicle cup holders. It's a genuine, factory-tough accessory specifically engineered to securely hold FISHER hand-held or joystick controls and all types of smart phone devices (not included with mount). This flexible gooseneck mount has a 360-degree rotation and ensures optimal, customizable positioning.
Part Number:
#82006 For All Models
Dielectric Grease
Keep your FISHER plow running strong. Apply our specially formulated dielectric grease after each use to prevent corrosion caused by electrolysis and highly corrosive de-icing agents.
Part Number:
#22400K 2 oz tube
Freeze Guard Grease
Specially formulated to protect moving components in arctic mining conditions, this grease is ideal for bearings, hinges and pivot bolts on snow and ice control equipment. The custom formula maintains viscosity from -40 up to 300 degrees, and military-grade, corrosion-prevention additives protect equipment from corrosion without harmful environmental impact. FREEZE GUARD Grease is available in cartridges, pails, totes and drums.
Part Number:
#72901 14oz. Cartridges
#72902 7 lb Pail
#72903 120 lb Tote
#72904 400 lb Drum
Pre-Wet System
The pre-wet system accessory allows the operator to activate deicing material by applying a liquid deicing agent directly on the material prior to leaving the hopper, providing you with increased material efficiency and superior ice control.
Part Number:
#76400 ON/OFF Pump Kit
#76420 Full Feature Pump Kit, FISHER
#76425 Pre-Wet 50 gal Tank Kit* (Two 25 Gal Tanks)
*Additional tank kits are not compatible with a vibrator
Central Point Grease Kit
The Central Point Grease Kit provides easy access to grease points, simplifying preventative maintenance greasing that is essential to maximize bearing life.
Part Number:
#11763 For 0.7 cu yd Models
Vibrator Kit
Designed to help move stubborn material and prevent bridging, a genuine FISHER Vibrator system will ensure that less-than-ideal material, which is prone to bridging and clogging, will not hold you up when you need to be on the move.
Part Number:
#76668 For All FLEET FLEX Models*
#78195 For All non-FLEET FLEX Models*
*Only compatible with one 50 gal pre-wet tank kit or one 100 gal pre-wet tank kit
License Plate Kit
Stay legal with our quality illuminated License Plate Kit. This genuine FISHER license plate kit has been specifically designed for your hopper and allows you to move your license plate to a spot that is visible and legally compliant.
Part Number:
#78197 For All Models
Strobe Light Kit
Make sure you're seen, day or night, with our complete hopper Strobe Light system. Constructed from high impact plastic, and rated beyond -20º F, this yellow LED strobe system has been designed to last and will ensure that you're seen in even the worst of conditions.
Part Number:
#99766 For All FLEET FLEX Models
Work Light Kit
A genuine FISHER Work Light system will grant you increased visibility at the rear of your spreader. Encased in anodized aluminum, and rated beyond -20deg F, this LED Work Light system projects over 1000 lumens to help you monitor material distribution and illuminate potential hazards while backing up.
Part Number:
#99505-1 For FLEET FLEX Models
#78198 For All Non-FLEET FLEX Models
Secondary Work Light Kit
Take it up a notch with a genuine FISHER secondary work light kit. Designed to integrate with our work light kit (99505-1), this accessory kit will provide an addition 1000 lumens of light on the opposite side of your FISHER spreader.
Part Number:
#99732-1 For FLEET FLEX Models
Ratchet Tie-Down Kit
This Tie-Down Kit provides additional in-bed stability and security. The 4000 pound, high-strength shipping straps allow you to add an extra measure of safety as you move tons of salt down the road. Each kit includes four ratchet tie down assemblies. (Hoppers require bolting to the truck frame for proper operator safety.)
Part Number:
#68790 For All Models
Stainless Steel Inverted V Kit
Reduce heavy startup loads on the drive train and reduce bridging during operations with a genuine FISHER Inverted V. Made of 12-gauge 201 stainless steel, the Inverted V is manufactured to be corrosion-resistant and stand up to the most demanding environments. The Inverted V Kit is easy to install and includes all of the necessary hardware and instructions.
Part Number:
#78150 For 1.5 cu yd Models
#78120 For 1.8 & 2.5 cu yd Models
Vehicle-Side Harness Kit
The Vehicle-Side Harness Kit contains components to replace harnessing on the truck or wire a second truck to operate the spreader.
Part Number:
#78402 For 0.7 cu yd Models
#85692 For 0.35 cu yd Models
Spreader Control Adapter Plate for Cup Holder Mount
Gain the flexibility and easy installation benefits of the cup holder control mount with every spreader installation using the new Spreader Control Adapter Plate Kit. Kit contains a durable metal mounting plate and hardware. Cup Holder Mount not included, order separately (#82006).
Part Number:
#82018 For All Models
Control Cup Holder Mount
The Control Cup Holder Mount is designed to fit firmly in most vehicle cup holders. It's a genuine, factory-tough accessory specifically engineered to securely hold FISHER hand-held or joystick controls and all types of smart phone devices (not included with mount). This flexible gooseneck mount has a 360-degree rotation and ensures optimal, customizable positioning.
Part Number:
#82006 For All Models
Trilogy Defense Pre-Wet & Liquid Application
For the first time, direct liquid application is available to Fisher Nation with truck de-icing equipment. The Trilogy Defense accessory system allows you to spread, pre-wet, and spray all with one hopper spreader.
Part Number:
#93265 Two 25 Gallon Tanks (For 1.5 & 2.2 cu yd Models)
#93270 Four 50 Gallon Tanks (For 3.0, 4.0, and 5.0 cu yd Models)
#93275 Two 50 Gallon Tanks (For 3.0, 4.0, and 5.0 cu yd Models)
Rearview Material Monitoring Camera
Easily view your material output from the comfort of your cab by using the material monitoring camera. It attaches to the top of your spreader with an LED light for additional visibility during nighttime operations. The monitor is installed inside your cab so you can ensure a smooth spread pattern and optimal material output.
Part Number:
#31210 For All Models
6" Side Extensions
Increase the capacity of your TEMPEST hopper spreader with the 6″ Side Extensions Kit. The increase in capacity will vary depending on the size of your spreader; increased material capacity will vary from 0.5 to 1 yard. Each kit contains fully stainless steel side walls and hardware to minimize corrosion and maintain a clean look. Pre-cut knockouts allow for easy installation of additional accessories and prevent the need to drill.
Part Number:
#93980 50" Kit for Additional 0.5 Yard
(For 1.5 & 2.2 cu yd Models)
#93985 70" Kit for Additional 1 Yard
(For 3.0, 4.0 & 5.0 cu yd Models)
Spill Guard
Available in 50" and 70" widths to cover the full range of TEMPEST hopper spreaders, the Spill Guard Kit provides the loader with an improved line of sight to the hopper edges, while preventing material from overflowing into the bed of the truck from off-center loading.
Part Number:
#93970 50" Kit (For 1.5 & 2.2 cu yd Models)
#93975 70" Kit (For 3.0, 4.0 & 5.0 cu yd Models)
Central Point Grease Kit
The Central Point Grease Kit provides easy access to grease points, simplifying preventative maintenance greasing that is essential to maximize bearing life.
Part Number:
#11763-1 For 1.5 - 5.0 cu yd Models
Pullover Tarp Kit
Protect de-icing material from the elements and lock out moisture to prevent material bridging with a pullover tarp. Fitted to the hoppers dimensions, the tarp features reinforced corners and potential wear points, cutouts to prevent interference with FISHER Strobe and Worklight brackets, and a cutout for the new Rearview Material Monitoring Camera and mounting bracket. Comes standard with durable, rubber bungees for simple and secure install and removal.
* Only available for 1.5 & 2.2 cu yd models
Part Number:
#93474 7' (For 1.5 cu yd Models
#93476 8' (For 2.2 cu yd Models)
Ratchet Tie-Down Kit
Positive locking mount with ratchet-strap assist provides additional in-bed stability, security, and simplifies installation for multiple vehicle types. Hopper spreaders require bolting to the truck frame for proper operator safety.
Part Number:
#68790 For All Models
Tie-Down Chain Kit
A Tie-Down Chain Kit provides additional in-bed stability and security. 72 inches of high-strength steel chain and binder allow you to add an extra measure of safety as you move tons of material down the road. Each kit contains four chain binder assemblies.
Hoppers require bolting to the truck frame for proper operator safety.
Part Number:
#99690 For All Models
Vibrator Kit
Designed to help move stubborn material and prevent bridging, a genuine FISHER Vibrator system will ensure that less-than-ideal material, which is prone to bridging and clogging, will not hold you up when you need to be on the move.
Part Number:
#76668-1 For All Models
Inverted V
Reduce heavy startup loads on the drivetrain and potential bridging during operations with the optional inverted V. Made of 12 gauge 201 stainless steel, the inverted V is strong and corrosion resistant, for use in highly demanding environments. The inverted V is easy to assemble and install and will provide years of trouble free use.
* Only accessory for 1.5 & 2.2 cu yd Chain Models (S150C & S220C)
* Standard on 1.5 & 2.2 cu yd Auger Models. (S150A & S220A)
* Standard on 3.0, 4.0 & 5.0 cu yd Chain & Auger Models. (S300C, S300A, S400C, S400A, S500C & S500A)
Part Number:
#93990 For 1.5 cu yd Chain Models
#93995 For 2.2 cu yd Chain Models
LED Work Light Kit (Primary)
A genuine FISHER LED Work Light system will grant you increased visibility at the rear of your spreader. Encased in anodized aluminum, and rated beyond -20deg F, this LED Work Light system projects over 1000 lumens to help you monitor material distribution and illuminate potential hazards while backing up.
Part Number:
#99505-1 For All Models
LED Work Light Kit (Secondary)
A genuine FISHER LED Work Light system will grant you increased visibility at the rear of your spreader. Encased in anodized aluminum, and rated beyond -20deg F, this LED Work Light system projects over 1000 lumens to help you monitor material distribution and illuminate potential hazards while backing up.
Part Number:
#99732-1 For All Models
LED Strobe Light Kit
Make sure you're seen, day or night, with our complete hopper LED Strobe Light system. Constructed from high impact plastic, and rated beyond -20º F, this yellow LED strobe system has been designed to last and will ensure that you’re seen in even the worst of conditions.
Part Number:
#99494-1 For All Models
Trilogy Defense Pre-Wet & Liquid Application
For the first time, direct liquid application is available to Fisher Nation with truck de-icing equipment. The Trilogy Defense accessory system allows you to spread, pre-wet, and spray all with one hopper spreader.
* Only available for 0.7 cu yd models
Part Number:
#85695 Two 25 Gallon Tanks (For 0.7 cu yd Models)
Rearview Material Monitoring Camera
Easily view your material output from the comfort of your cab by using the material monitoring camera. It attaches to the top of your spreader with an LED light for additional visibility during nighttime operations. The monitor is installed inside your cab so you can ensure a smooth spread pattern and optimal material output.
Part Number:
#31210 For All Models
Side Extensions
An extension collar is available as an accessory to increase material capacity for vehicles that can handle the additional weight. 0.25 cu yd extension collars available for the 0.35 cu yd hoppers and 0.5 cu yd extension collars available for the 0.7 cu yd hoppers.
Part Number:
#85698 For 0.35 cu yd Models
#85699 For 0.7 cu yd Models
Spill Guard
Available in 50" and 70" widths to cover the full range of TEMPEST hopper spreaders, the Spill Guard Kit provides the loader with an improved line of sight to the hopper edges, while preventing material from overflowing into the bed of the truck from off-center loading.
Part Number:
#85696 For 0.35 cu yd Models
#85697 For 0.7 cu yd Models
Ratchet Tie-Down Kit
Positive locking mount with ratchet-strap assist provides additional in-bed stability, security, and simplifies installation for multiple vehicle types. Hopper spreaders require bolting to the truck frame for proper operator safety.
Part Number:
#68790 For All Models
Pullover Tarp Kit
Protect de-icing material from the elements and lock out moisture to prevent material bridging with a pullover tarp. Fitted to the hoppers dimensions, the tarp kit is held securely in place with included durable rubber bungees.
* Only available for 1.5 & 2.2 cu yd models
Part Number:
#30059 For 0.35 cu yd Models
#30061 For 0.7 cu yd Models
Vibrator Kit
Designed to help move stubborn material and prevent bridging, a genuine FISHER Vibrator system will ensure that less-than-ideal material, which is prone to bridging and clogging, will not hold you up when you need to be on the move.
Part Number:
#76668-1 For All Models
Inverted V
Reduce heavy startup loads on the drivetrain and potential bridging during operations with the optional inverted V. Made of 12 gauge 201 stainless steel, the inverted V is strong and corrosion resistant, for use in highly demanding environments. The inverted V is easy to assemble and install and will provide years of trouble free use.
Part Number:
#85706 For 0.35 cu yd Models
#85707 For 0.7 cu yd Models
Truck Upfit Kit
This kit contains a longer truck harness, license plate kit, CHMSL kit, and a ratchet tie down kit so the 0.35 cu yd hopper can be used in place of an auger tailgate spreader when using sand.
Part Number:
#85693 For 0.35 cu yd Models
Vehicle-Side Harness (Fleet Flex)
The Vehicle-Side Harness Kit contains components to replace harnessing on the truck or wire a second truck to operate the spreader.
Part Number:
#85692 For 0.35 cu yd Models
#78402 For 0.7 cu yd Models
License Plate Kit
Stay street legal with this illuminated License Plate Kit for your alternate license plate location. Providing convenient mount methods and lighting in a high impact plastic casing, the license plate kit allows you to move your license to a spot that is visible and legally compliant. Don’t leave without it.
* Required if using 0.35 cu yd hopper on a truck
Part Number:
#85694 For 0.35 cu yd Models
LED Strobe Light Kit
Make sure you're seen, day or night, with our complete hopper LED Strobe Light system. Constructed from high impact plastic, and rated beyond -20º F, this yellow LED strobe system has been designed to last and will ensure that you’re seen in even the worst of conditions.
Part Number:
#99494-1 For All Models
LED Work Light Kit (Primary)
A genuine FISHER LED Work Light system will grant you increased visibility at the rear of your spreader. Encased in anodized aluminum, and rated beyond -20deg F, this LED Work Light system projects over 1000 lumens to help you monitor material distribution and illuminate potential hazards while backing up.
Part Number:
#99505-1 For All Models
LED Work Light Kit (Secondary)
A genuine FISHER LED Work Light system will grant you increased visibility at the rear of your spreader. Encased in anodized aluminum, and rated beyond -20deg F, this LED Work Light system projects over 1000 lumens to help you monitor material distribution and illuminate potential hazards while backing up.
Part Number:
#99732-1 For All Models
